Analog Transmission Systems  (629)

The NVT Model NV-1613S is a compact 16-channel passive transceiver hub that allows transmission of real-time monochrome or colour video over Unshielded Twisted-Pair (UTP) cable. Baseband (composite) signals of any type are supported. “Up-the-coax” type signal may be sent over the same wire pair at distances up to 750ft (225m).The unparalleled interference rejection ability of the model NV-1613S hub allows video signals to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. Perfect for larger CCTV installations where port density and camera number growth are prevalent. With built-in transient protection, damaging voltage spike problems are eliminated. Features: Compact rack mountable 19" 1U high enclosure features 16-channelsand is only 1.54" (40mm) deep Use with any NVT passive transceiver or hub for full motion CCTV at distances up to 750ft (225m) Use with any NVT active receiver or hub as a rack-mountable passivetransmitter for distances up to 3,000ft (1km) RJ45 video connectivity with optional NV-RJ45A RJ45 to-screw-terminal adaptors (included) No power required Exceptional interference rejection Built-in transient protection Supports “up-the coax” type control signal up to 750ft (225m) Compatible with qualified UTP cameras Limited lifetime warranty

Provides transmission of 8 video channels, 2 duplex 128kbps data channels, 2 CD quality duplex audio channels and 2 contact closure channels on one singlemode or multimode optical fibre. 

X-Net 8 x simplex video channel transmit/receive module, including 1 x 10/100 BaseT Ethernet, 2 x duplex data, 1 x duplex audio, 2 x duplex contact closure channels. Utilises 2 rack slots. 

Compact stand-alone sending unit for video, audio and data transmission via ISDN. Full duplex audio transmission. Remote maintenance and software upgrade via ISDN. Remotely controlled from ViewStation receiver.

Small size, less than 2" deep. Supports screw-terminal or RJ45 UTP video inputs. Built-in transient protection. Supports "up-the-coax" type control signal up to 750 ft. Transmit up to 750ft, 3000ft with an active receiver. The NVT Model NV-3213S is a compact 32-channel passive transceiver hub that allows transmission of real-time monochrome or colour video over Unshielded Twisted-Pair (UTP) telephone wire. Baseband (composite) signals of any type are supported.

Mono or colour non-amplified passive video/audio transceiver. Network Wiring: one unshielded twisted pair 24 AWG (0,5 mm) or thicker. Impedance: 100 ± 20 ohms. Male BNC supports on-camera mounting. Built-in transient protection. Supports "up-the-coax" type control signal up to 750 ft  Transmit up to 750 ft, 3000 ft with active receiver.

The versatile VAD 5200 series transceivers digitise and transmit one video signal while also handling one full-duplex data/audio channel over one multimode or single mode optical fibre.  The high-speed data channel is fully transparent and suitable for RS-232, RS-422/485, TTY, Manchester and biphase signals.  VAD 5210 model has MM fibre type and 1300/850 nm wavelength; VAD 5250 model has SM fibre type and 1310/1550 nm wavelength. All VAD 5200 equipment is SNM compatible.

Compact stand-alone sending unit for video, audio and data transmission via ISDN. Full duplex audio transmission. Remote maintenance and software upgrade via ISDN. Remotely controlled from ViewStation receiver.

The NVT Model NV-RM 15 Rackmount Video/Audio Transceiver System allows the co-location of up to fifteen NVT Video/Audio Transceivers in one compact enclosure. Panels can reside in the same rack as other equipment, such as switchers, multiplexers, video conferencing equipment, etc.

Real time transmission unit with WRS3-AD or WRS3-M reception software. Connections-Internet, LAN, ISDN, leased line, PSTN, mobile network. Built-in web server. Support static and dynamic IP. Image refreshing rate up to 25 or 30fps over LAN. Automatic alarm call back. Single and multi-site monitoring. External Modem.

Building up an expensive company-wide CCTV network is no longer required.  TeleEye III+ single channel video transmitter (VT3-1CA) can "incorporate" video surveillance and "connect" any video camera to an existing LAN.  It saves unnecessary cabling and installation costs and allows users to monitor video from any PC workstation inside the premises.Key features include:Built in Web server Up to 25 frames per second over LAN Supports IP connectivity Mobile video on pocket PC Home page video tools

Real time transmission unit with WRS3-AD or WRS3-M reception software. Connections-Internet, LAN, ISDN, leased line, PSTN, mobile network. Built-in web server. Support static and dynamic IP. Image refreshing rate up to 25 or 30fps over LAN. Automatic alarm call back. Single and multi-site monitoring. External Modem.

Flexible connections - Internet, LAN, ISDN, leased line, PSTN, mobile network. Built-in server. External modem. Supports static and dynamic IP. High quality resolution up to 640x480 pixels. Digital video recording. Automatic alarm call back. Compatibility with popular 3rd party telemetry systems. Single- and multi-site monitoring. Audio transmission with CAMERIO teleEAR.

Omnidirectional SMA male rubber duck antenna.  FCC / IC / CE approved.  Includes 12VDC power supply.  RCA female stereo audio connection (600Ohms, 1Vp-p).  Radiated power: 50mV/m @ 3m.

X-Net 1 x simplex video channel transmit/receive module, including 1 x 10/100 BaseT Ethernet, 1 x duplex data, 1 x duplex contact closure channel. Utilises 1 rack/box slot. 

Video Twisted Pair Transmitter

Rackmount housing or standalone.

COE Ltd demonstrates its X-Net video transmission system with its powerful analytics system (X-Net VI) and network video recorder (X-Net NVR).COE X-Net VI is a powerful distributed analytics system taking advantage of the DSP in the X-Net G3 MPEG4 video codec.  Analysis functions include motion/non-motion object tracking.  Key advantages of our system are:Lower false alarm rates (FAR) due to analysis placed prior to digitisationCentral server able to handle 100+ simultaneous video streamsMulti-rule operation on the same video streamVideo not required at the central location to carry out analysis hence lower network bandwidth used - video only streamed when requiredSMS message function for sending the alarm text and picture to any mobile phone/PDAX-Net NVR enhances the transmission and management of video by offering a network wide recording solution for IP and analogue video streams.  The recording software operates on a standard dual core  PC and will manage NAS and RAID based disk arrays.  Key features include:Pre/post alarm event managementArchive onto DVD for evidential useMulti-client and server architecture for flexible system definitionMultiple video stream views on client terminals for ‘mosaic' screen setupsPowerful search functions commonly found on DVR's for fast retrieval of video footageIntegrated with X-Net VI for alarm management and automated response functions upon incident detection

X-Net 2 x simplex video channel transmit/receive module, including 1 x 10/100 BaseT Ethernet, 1 x duplex data, 1 x duplex contact closure channels. Utilises 1 rack/box slot. 

Supports screw-terminal UTP video inputs. Built-in transient protection & ground lifting. Three-position distance range switch. Mono or colour non-amplified video receiver up to 2.4km with Cat-5 wire to be used with NV-652R, NV-852R, or NV-1662R receivers. Network Wiring: One Unshielded Twisted Pair 24 AWG (0,5 mm) or thicker. Impedance: 100 ± 20 ohms. Built-in transient protection & ground lifting. Built-in brightness & sharpness controls; blue power LED, green active LED. Compatible with qualified UTP cameras. Up to 10 NV-653Ts may be rack mounted using the NV-RM8/10 Rack Panel Kit.

Modular Digital Video Equipment for video security applications over IP or ATM networks. Up to ten slots for VisioWave PCI-1 video codec boards or optional modules can be used. Optional ATM 155, serial and digital I/O modules. Optional SCSI interface for connection to VisioWave HQI RAID. Storage module. Uses VisioWave Security software.

Bi-directional, 12 Bit Video, 24 Bit Audio & Data Fiber Optic Multiplexer. Available in portable, rack-mount and modular configurations. Applications include links from studio to transmitter (STL), studio to studio, studio to CATV head-end, common carrier, RBOC Telco circuits, distance learning, Intelligent Transportation Systems & back-haul feeds from special events.

Radiated power 80 mV/m.  Omni-directional transmitter and receiver.  RCA male audio connection @ 600 Ohms, 1Vp-p.  FCC / IC approved. Bare lead for alarms.

The NVT Model NV-213A Video Transceivers are passive (non-amplified) device that allows the transmission of real-time monochrome or color video over Unshielded Twisted-Pair (UTP) telephone wire. Baseband (composite) signals of any type are supported.

Converts 24 VAC to 12 VDC. Male BNC connector supports camera mounting. Built-in transient protection. Transmit video up to 750 ft, 3000 ft with an active receiver. The NV-226J-PV Video Transmitter +12VDC Converter is a passive (non-amplified) video transmitter combined with a 24 VAC to 12 VDC converter.

Radiated power 900 mW.  Omnidirectional antenna.  RCA male audio connection @ 600 Ohms, 1Vp-p.

Combination of ADS1200 TRA and ADS1200 TRB fibre audio-data multiplexers.  Full duplex RS-422/485, RS-232 and audio over one or two fibres.  Modular design in compact form.  Single fibre audio data multiplexer A/B side.  850/1300 nm wavelength with 15dB budget.  Rack mount housing.

TCP/IP and SNMP software package option.

The VAD 5100 series transmitters and receivers digitise and transmit one video signal while simultaneously handling two streams of simplex data, contact closure and audio signal, all over one multimode or single-mode optical fibre. The high speed data channels are fully transparent and suitable for RS-232, RS-422/485, TTY, Manchester and biphase signals. VAD 5110 model has MM fibre type and 1310 nm wavelength; VAD 5150 model has SM fibre type and 1310 nm wavelength.

The NVT Model NV-1662 is a 16-channel active (amplified) distribution amplifier device that allows the transmission of real-time monochrome or color video on up to one mile (1,6km) using Category Unshielded Twisted-Pair (UTP) wire.

Radiated power 100 mV/m @ 3m.  Directional antenna.  FCC / IC approved.  RCA male audio connection @ 600Ohms, 1Vp-p.

Bi-Directional Video, Audio, and Data over single or pair of fibre optic cable. Compatible with NTSC, RS-170 PAL, and CCIR Video-Formats. Adjustment Free Uncompressed Digital Transmission up to 50 Km. NMS (GUI) Monitor Package. TCP/IP and SNMP Software package option overview.

12 Bit or 24 Bit (DVM-2200) video audio fiber optic multiplexer. Available in portable, rack-mount and modular configurations with all optical wavelengths, LED Multimode and Laser Single-mode. Supports analog video, analog audio, serial digital video and digital audio in the same tray.

The NVT Model NV-418AR Dual Video/Audio Transceiver is a rack-mount passive (non-amplified)device that allows transmission of real-time monochrome or color video and audio over UnshieldedTwisted-Pair (UTP) telephone wire. Baseband (composite) signals of any type are supported.

Resolution up to 640x480 pixels. Auto dial-up upon alarm event. Remote telemetry control. Self diagnostic and recovery. Easy installation and configuration. 1 RCA audio input/output.

Built-in automatic gain control allows plug and play installation and maintenance free operation. VBS 2040 transmitter and receivers are available in rack-mount housings. The VBS 2040/2050 rack-mount transmitter and receiver models for single-mode fiber are SNM compatible. Other features include wavelength of 1300 nm and fibre type SM (single mode).

The COE Series 4 product range is designed to combine video and data signals on a single optical fiber in a high performance and robust package. It is available in Eurocard and boxed format with all connections provided via two part connectors.

Radiated power 50 mV/m @ 3m.  Directional antenna.  FCC / IC approved.  RCA male audio connection @ 600Ohms, 1 Vp-p.  FCC / IC approved.

The Multidyne DVM-2D is a fiber optic digital multiplexer designed to transmit 2 channels of video, 2 channels of audio, and/or 2 channels of data over a fiber optic cable. Compatible with NTSC, PAL and CCIR video and standard data interfaces such as RS-232, RS-422, and TTL.

Video transmission via GSM 900/1800. Resolution up to 640x480 pixels. Auto dial-up upon alarm event. Remote telemetry control. Self diagnostic and recovery. Easy installation and configuration.